[Jul 30, 2023] Free CIP Level 2 NACE-CIP2-001 Exam Question
NACE-CIP2-001 dumps & CIP Level 2 sure practice dumps
NEW QUESTION # 41
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. mild steel.
- C. iron
- D. aluminum
Answer: A,D
NEW QUESTION # 42
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION # 43
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. afford limited temperature insulation.
- C. reduce magnetic polarity.
- D. protect the transported product.
Answer: D
NEW QUESTION # 44
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Preferential fuel for the fire
- C. Explosion resistance
- D. fire extinguishing characteristics
Answer: A
NEW QUESTION # 45
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION # 46
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Consult SSPC Guide 1 prior to use
- B. Determine the Dry Film Thickness of the coating prior to use
- C. Ensure the glue on the dolly is properly applied prior to use
- D. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
Answer: B
NEW QUESTION # 47
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Transmission
- C. Distribution
- D. Gathering
Answer: C
NEW QUESTION # 48
Generally for safety considerations, waterjetting hose connections use
- A. filters.
- B. a whip-lock device.
- C. a long wand.
- D. an oil/water separator.
Answer: B
NEW QUESTION # 49
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Request clarification from the specifier
- C. Call your supervisor
- D. Ignore the additional requirement
Answer: A
NEW QUESTION # 50
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- B. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- C. Correct the errors yourself and suggest the Level 1 inspector be replaced
- D. Correct the errors yourself and submit the reports without any further action
Answer: B
NEW QUESTION # 51
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A destructive paint inspection Tooke gauge
- C. A mechanical adhesion tester
- D. A set of 14 pencils of varying hardness
Answer: B
NEW QUESTION # 52
Pre-cleaning of work pieces will NOT remove
- A. snow, ice or water.
- B. oil or grease.
- C. dirt.
- D. mill scale.
Answer: D
NEW QUESTION # 53
Inspection and Test plans are developed by referencing:
- A. The Specification, Application Guidelines, 'Relevant Standards and Codes
- B. The Specification, SDS, relevant Standards and Codes
- C. The Specification, Safety Manual, Relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION # 54
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. To supersede the requirements of the product data sheets
- C. Outline the inspection steps, sequencing and pass/fail criteria
- D. So the contractor has a single document to reference
Answer: C
NEW QUESTION # 55
You can use magnifiers to examine all of the following EXCEPT
- A. Mill scale
- B. Surface cleanliness
- C. Blisters
- D. Surface profile
Answer: B
NEW QUESTION # 56
Which is used to calibrate a pH meter?
- A. Standard solvent solution
- B. Deionized water
- C. Standard buffer solution
- D. Distilled water
Answer: C
NEW QUESTION # 57
The HATE adhesion tester uses
- A. mechanical means only to apply pressure to the test dolly.
- B. compressed air to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. a hydraulic piston to apply pressure to the test dolly.
Answer: D
NEW QUESTION # 58
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of chemical exposure
- B. a), b), and c)
- C. Risk of acid or caustic splashes
- D. Risk of skin
Answer: B
NEW QUESTION # 59
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to scope of your role
- B. Accept assignment without hesitation
- C. Review the NACE Attestation prior to making a decision
- D. Advise the prospective employer that you cannot accept the position
Answer: C
NEW QUESTION # 60
A single component water borne acrylic coating cures by:
- A. Coalescence
- B. Solvent Evaporation
- C. Co-Reaction
- D. Oxidation
Answer: A
NEW QUESTION # 61
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage DC Pulse Type
- B. Low Voltage Sponge Type
- C. High Voltage AC
- D. High Voltage DC Constant Current
Answer: D
NEW QUESTION # 62
......
NACE-CIP2-001 certification exam is a rigorous assessment that covers a wide range of topics related to the inspection of coatings. NACE-CIP2-001 exam consists of 120 multiple-choice questions, which must be completed within four hours. NACE-CIP2-001 exam is designed to test the individual’s knowledge of coating inspection techniques, surface preparation methods, coating application procedures, and documentation requirements. NACE-CIP2-001 exam is also designed to evaluate the individual’s ability to identify and solve problems that may arise during the inspection process.
NACE NACE-CIP2-001 Actual Questions and Braindumps: https://lead2pass.pdfbraindumps.com/NACE-CIP2-001_valid-braindumps.html